- Best Seller Products

The High-Fidelity Pwo proofreading DNA polymerase from Genaxxon bioscience is a thermostable, highly processive enzyme possessing 5'-3' DNA polymerase with additional 3'-5' proofreading exonuclease activity, which enables the correction of nucleotide incorporation errors. It has no 5'→3' exonuclease activity. The High-Fidelity Pwo DNA polymerase is a recombinant form of the hyperthermophilic archaebacteria Pyrococcus woesei. Pwo proofreading DNA polymerase shows an increased thermostability and a 10-times higher accuracy compared to Taq DNA polymerase. A mixture of Taq DNA Polymerase and Pwo DNA polymerase provides more robust synthesis of longer amplification products (Barnes, 1994. Proc. Natl. Acad. Sci. USA 91:2216-2220). Test sample available at a special price! The test sample price will be refunded on the first official order of the product. Features: 10-times higher accuracy compared to Taq DNA polymerase High-Fidelity polymerase Proofreading function (3' - 5' exonuclease activity) High thermo stability Generates blunt-end PCR products Generates PCR products for cloning and expression More High-Fidelity Proofreading Polymerases from Genaxxon bioscience:- M3003 ReproFast Proofreading Polymerase- M3004 Pfu Proofreading Polymerase- M3012 ReproHot (KOD) Proofreading Polymerase - AQ97 High Fidelity proofreading Polymerase With our high quality dNTPs as Set (M3015) or Mix (M3016) or our DNA Ladders and our favourable standard agarose (M3044) we can offer additional products for your PCR.

The High-Fidelity Pfu proofreading DNA polymerase from Genaxxon bioscience is a thermostable, highly processive enzyme possessing 5'-3' DNA polymerase with additional 3'-5' proofreading exonuclease activity, which enables the correction of nucleotide incorporation errors. It has no 5'→3' exonuclease activity. The High-Fidelity Pfu DNA polymerase is a recombinant form of the hyperthermophilic archaebacteria Pyrococcus furiosus (Pfu). Pfu proofreading DNA polymerase shows an increased thermostability and a 10-times higher accuracy compared to Taq DNA polymerase. A mixture of Taq DNA Polymerase and Pfu DNA polymerase provides more robust synthesis of longer amplification products (Barnes, 1994. Proc. Natl. Acad. Sci. USA 91:2216-2220). Test sample available at a special price! The test sample price will be refunded on the first official order of the product. Features: 10-times higher accuracy compared to Taq DNA polymerase High-Fidelity polymerase Proofreading function (3' - 5' exonuclease activity) High thermo stability Generates blunt-end PCR products Generates PCR products for cloning and expression More High-Fidelity Proofreading Polymerases from Genaxxon bioscience:- M3003 ReproFast Proofreading Polymerase- M3002 Pwo Proofreading Polymerase- M3012 ReproHot (KOD) Proofreading Polymerase - AQ97 High Fidelity proofreading Polymerase With our high quality dNTPs as Set (M3015) or Mix (M3016) or our DNA Ladders and our favourable standard agarose (M3044) we can offer additional products for your PCR.

Overview:Proteinase K is a robust and versatile serine protease used extensively in molecular biology for the digestion of proteins in nucleic acid preparations. This solution, at a concentration of 20 mg/mL, is ideal for a wide range of applications including the preparation of DNA and RNA samples. The PCR grade quality ensures that the enzyme is free from contaminants that could interfere with downstream applications, making it highly suitable for sensitive techniques such as PCR.Product Details:ready-to-useConcentration: 20 mg/mLactive over a wide range of reaction conditionsAn elevation of the reaction temperature from 37°C to 50 - 60°C may increase the activity several timesQuality: PCR grade, ensuring high purity and no interference with PCR reactions.Applications: Suitable for DNA and RNA extractionRemoval of protein contaminantsPreparation of samples for various molecular biology techniques.Benefits:High Purity: The PCR grade quality guarantees minimal contamination, ensuring reliable results in sensitive applications. Versatility: Ideal for various molecular biology procedures, including sample preparation for PCR.Convenience: Ready-to-use solution at an optimal concentration for ease of use. Notes:The recommended working concentration of Proteinase K is 0.05 to 1 mg/mL. The activity of the enzyme is stimulated by 0.2 to 1% SDS and also by 1 to 4M ureaCa2+ protects Proteinase K against autolysis and increases the thermal stabilityStable over a wide pH range: 4.0 to 12.5, optimum pH 7.5 to 8.0Activity optimum: 50°C to 55°CRapid denaturation of enzyme occurs at temperatures above 65°CFeatures:No detected exonuclease, endonuclease or RNase activityConcentration ≥20 mg/mL / Activity ≥800 U/mLDNA content ≤200 pg/mLShipping conditions: Shipment on wet ice Storage buffer: 10 mM Tris/HCl, pH7.5; 1mM (CH3COO)2Ca; 50% glycerolProteinase K can be obtained from Genaxxon as Powder (M3036) > or as 20mg/mL Solution (M3037) >.Produced by Genaxxon bioscience GmbH, founded in 2002 by Dr. Norbert Tröndle to provide reliable products for PCR and custom cell culture media formulations, the Proteinase K Solution 20 mg/mL offers a dependable and efficient solution for your molecular biology needs. Achieve consistent, high-quality results with an enzyme designed specifically for your requirements.

Agarose LE is a standard agarose for the separation of DNA in the size range between 100bp and 25kbp. It is suitable for all analytical and preparative electrophoresis of nucleic acids in routine gel electrophoresis. Depending on the concentration of Agarose LE used, the size range of nucleic acid separation will vary between 100bp and 25kbp. The low EEO makes this useful for a broad range of applications: PCR product analysis, restriction enzyme digest analysis, separation of RNA before blotting, etc. This agarose is comparable with, e.g. Agarose BioRagent, low EEO from Sigma or with the Universal-Agarose, peqGOLD from Peqlab. Free Taq DNA Polymerase test sample available! No shipping costs within Germany. Genaxxon offers Agaroses for different purposes. Two melting point options and normal or high resolution separation of DNA fragments are available. Standard normal melting agarose M3044 with standard resolution used in routine DNA electrophoresis for separation of a wide range of DNA fragments from 100bp up to 25kbp. This agarose is available as powder (M3044 Agarose LE >) or as high-quality, multi-purpose tablets (M3054 >) available in blister packaging in 200 or 1,000 tablet quantities. They are compact, pre-weight and therefore easy-to-use. Low melting/gelling temperature agarose recommended for rapid DNA gel extraction with the agarose-digesting enzyme, agarase, as well as for "in-gel" DNA treatment with enzymes or for bacterial transformation with nucleic acids directly after re-melting the gel. High resolution agarose (normal melting or low melting) for high resolution elektrophoresis to differentiate DNA fragments with only 2 bp size difference: M3046 Agarose Tiny > (low melt, high resolution comparable to NuSieve®), or M3047 Agarose Tiny HT > (high gel strength, high resolution comparable to SeaKem®). For the nontoxic staining of nucleic acids in agarose gels the highly sensitive fluorescent dye SafeGel red stain (M3193) or SafeGel green stain (M3191) is recommended.

Overview:Proteinase K is a robust and versatile serine protease used extensively in molecular biology for the digestion of proteins in nucleic acid preparations. This solution, at a concentration of 20 mg/mL, is ideal for a wide range of applications including the preparation of DNA and RNA samples. The PCR grade quality ensures that the enzyme is free from contaminants that could interfere with downstream applications, making it highly suitable for sensitive techniques such as PCR.Product Details:ready-to-useConcentration: 20 mg/mLactive over a wide range of reaction conditionsAn elevation of the reaction temperature from 37°C to 50 - 60°C may increase the activity several timesQuality: PCR grade, ensuring high purity and no interference with PCR reactions.Applications: Suitable for DNA and RNA extractionRemoval of protein contaminantsPreparation of samples for various molecular biology techniques.Benefits:High Purity: The PCR grade quality guarantees minimal contamination, ensuring reliable results in sensitive applications. Versatility: Ideal for various molecular biology procedures, including sample preparation for PCR.Convenience: Ready-to-use solution at an optimal concentration for ease of use. Notes:The recommended working concentration of Proteinase K is 0.05 to 1 mg/mL. The activity of the enzyme is stimulated by 0.2 to 1% SDS and also by 1 to 4M ureaCa2+ protects Proteinase K against autolysis and increases the thermal stabilityStable over a wide pH range: 4.0 to 12.5, optimum pH 7.5 to 8.0Activity optimum: 50°C to 55°CRapid denaturation of enzyme occurs at temperatures above 65°CFeatures:No detected exonuclease, endonuclease or RNase activitySpecific activity: >40 units/mg protein Activity: ≥30 units/mg lyophilizateSolubility: ≥20 mg/mLDNA content ≤10 pg/mgShipping conditions: Shipment on wet iceProteinase K can be obtained from Genaxxon as Powder (M3036) > or as 20mg/mL Solution (M3037) >.Produced by Genaxxon bioscience GmbH, founded in 2002 by Dr. Norbert Tröndle to provide reliable products for PCR and custom cell culture media formulations, the Proteinase K Solution 20 mg/mL offers a dependable and efficient solution for your molecular biology needs. Achieve consistent, high-quality results with an enzyme designed specifically for your requirements.

Highly pure, HPLC purified (>99%) dNTPs packaged as 4 separate 100mM solutions of dATP, dCTP, dGTP and dTTP for qPCR, RT-PCR, standard PCR, and Klenow reactions. Genaxxon’s dNTP solutions have been optimized for use in DNA amplification and other related methods. Genaxxon dNTPs contain no measurable bacterial or human DNA. For long term storage and/or for repeated use, our recommendation is to aliquot the stock solutions. Solutions of dNTP sodium salts (dATP, dCTP, dGTP und dTTP) Concentration: 100 mM each nucleotide Please have also a look on our broad range of nucleotides especially the dNTP mixes with 2 mM or 10 mM or the modified nucleotides, e.g. Biotin-11-dUTP. You can get additional products for your successful PCR as our Taq DNA Polymerse (M3001), or our proof-reading polymerases Pfu (M3004), Pwo (M3002) and ReproFast (M3003) as well as the ready-to-use RedMastermix (M3029), already including dNTPs.

RedMasterMix (2x) - PCR MasterMix with red dye to help visualize pipetting and mixing steps. Electrophoresis can be performed immediately after PCR without the need of a gel loading buffer. This makes this MasterMix time efficient, cost efficient and a reliable choice for the best PCR results with high efficiency.  One tube, one pipetting step. RedMasterMix (2x) is delivered to you as a optimized, ready-to-use solution containing- Taq DNA Polymerase - dNTPs- MgCl2- a red dye- reaction bufferfor efficient amplification of DNA. Additionally the RedMasterMix (2x) contains an additive and a red dye for proceeding with electrophoresis after PCR without adding loading buffer. Just add your primers and template DNA. This PCR MasterMix (2x) has been optimized for use in routine PCR amplification of DNA templates in the range of 0.2-4kb. The special formulation of our PCR RedMasterMix (2x) can withstand repeated freezing/thawing without compromising yields, sensitivity or results, when used as directed. The PCR MasterMix with red dye is efficient (no left over of reagents), scalable from 10µL to 50µL and stable for at least 24 months.Our RedMastermix can also be used for Sanger sequencing. Just dilute the PCR reaction 1:8 after PCR, or purify using spin columns and then apply. Read now in our blog how Genaxxon's RedMasterMix can also simplify your laboratory work. Our Agaroses > and DNA Ladders > are ideally suited for subsequent electrophoresis of PCR products.

ProbeMasterMix FAST with 50nM ROX is optimised for fast qPCR assays with probes in block systems. The master mix is optimized for fast qPCR with short denaturation 2-step cycles. This 2X Mastermix is ready-to-use and contains all components for a successful and reliable qPCR with the exception of primer and template DNA Advantages of the Hotstart Taq polymerase used in the Genaxxon ProbeMasterMix: Hotstart technology enables setup of PCR mixture at room temperature. short initial denaturation of not more than 2 minutes. optimized for 2-step PCR protocols. No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon Hotstart Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The hotstart formulation inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Probe qPCR master mix with 50nM ROX contains all the necessary components in an optimized composition to carry out quantitative PCR. hotstart Taq DNA Polymerase dATP, dCTP, dGTP, dTTP optimized reaction buffer 50nM ROX as internal passive reference stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) This Mastermix is specially suited for the following instruments: Applied Biosystems® 7500, 7500 Fast and ViiA™ 7, QuantStudio™ instruments, Agilent Mx3000P™, Mx3005P™, Mx4000™ and AriaMx. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

SuperHot Taq DNA Polymerase is a superior DNA Polymerase for Real Time PCR, Hot-Start PCR, low-copy number PCR, or PCR of difficult templates. The enzyme is developed to enhance the specificity, sensitivity and yield of DNA amplification. SuperHot Taq DNA polymerase is a chemicaly modified form of thermostable DNA polymerase Taq, which is activated by heat treatment. A chemical moiety is attached to the enzyme at the active site, which renders the enzyme inactive at room temperature. Thus, during setup and before the first PCR cycle, the enzyme is not active and misprimed primers are not extended. As a result specifity and efficiency are increased by far compared to standard Taq DNA polymerase. Additionally, difficult targets with high GC-content can be amplified. For realtime PCR Genaxxon offers specially optimized 2-times qPCR mastermix >, respective a special Multiplex-PCR mastermix >. Features of Genaxxons SuperHot DNA Polymerase chemically modified increased specifity increased sensitivity for difficult templates with high GC-content Please have also a look on our SuperHot Taq 2-times Mastermix >. Even more convenient than the SuperHot Taq. With our high quality dNTPs as Set (M3015.4100 and M3015.0250) > or Mix (M3016.1010) > or our DNA Ladders > and favourable standard agarose (M3044) > we can offer additional products for your PCR.

ready-to-use PCR Mastermix with red Loading Dye for visual control of the pipetting steps and additional fluorescent dye for fast and easy detection of the DNA bands. After PCR, the PCR mix can be pipetted directly into the gel pockets without adding loading buffer. This makes our RedMasterMix Fluoro (2x) even more time- and cost-saving than our proven Red Mastermix. The RedMasterMix Fluoro (2x) with fluorescent gel staining dye and red loading dye also features high specificity for best results. The RedMasterMix Fluoro (2x) is a ready-to-use mixture of: - Taq DNA Polymerase- PCR reaction buffer- dNTPs- MgCl2- red loading dye- fluorescence gel staining dye for DNA band detection in an optimal concentration for efficient amplification of DNA templates by PCR. Only the primers and the template DNA have to be added. At the same time, the PCR Matermix contains an additive and a red dye, which allows subsequent electrophoresis without the addition of loading buffer. After electrophoresis, detection is performed directly under blue light without further staining. This saves additional time and costs. The RedMasterMix Fluoro (2x) with fluorescent dye was developed for use in routine PCR up to 4 kb amplicon length. The special composition of the buffer guarantees reproducible results even after repeated thawing and freezing cycles. Our Red MasterMix (2x) Fluoro is shipped in convenient aliquots of 1.25mL. For more information on our SimplyEnlight PCR products, read our blog now. Genaxxon's SimplyEnlight PCR - Unlock the Power of Your PCR!

Loading buffer I Fluoro is a fluorescent reagent that produces instant visualization of DNA bands upon blue light or UV illumination of agarose gels. Supplied in 6X DNA Loading Buffer, Loading buffer I Fluoro is used to prepare DNA markers or samples for loading on agarose or polyacrylamide gels.  Loading buffer I Fluoro is the sensitive staining reagent available for detecting the double-stranded DNA (dsDNA). It contains three tracking dyes (bromophenol blue, xylene cyanol FF, and orange G) for visually tracking the DNA migration during the electrophoresis plus an additional fluorescence dye for detection of DNA bands without an additional staining of the gel. It is an ideal alternative to Ethidium Bromide (EtBr). Approximate fluorescence excitation / emission: 300, 495 / 537 nm, bound to nucleic acid. For more information on our SimplyEnlight PCR products, read our blog now. Genaxxon's SimplyEnlight PCR - Unlock the Power of Your PCR! Picture 1: Comparison of UV- and blue light excitation             Picture 2: Effect of EtBr plus UV on cloning efficiency.

The GenLadder 100 bp Plus with gel staining dye and loading dye - ready-to-use is an innovation for high throughput approaches or colony screenings! Ideally suited to determine the size of double-stranded DNA between 100 and 1000 base pairs. The additional bands at 1.5kbp and 3.0kbp allow additional DNA sizes in this range to be assigned without having to use an additional 1kbp DNA marker. At the same time, the mixture also contains a fluorescent gel staining dye. Additional staining (pre- or post staining) or the addition of fluorescent dye prior to application is thus unnecessary and saves an additional pipetting step. At the same time, it is possible to check whether a PCR was successful or not before applying the PCR sample! This DNA ladder is an ideal match for our Red MasterMix Fluoro 2X, which also contains the gel staining dye. Together the ideal pair for Colony Screens! For more information on our SimplyEnlight PCR products, read our blog now. Genaxxon's SimplyEnlight PCR - Unlock the Power of Your PCR! The Gene Ladder 100 bp Plus consists of 12 fragments in sizes between 100 - 1000bp spaced 100bp apart. In addition, there are further bands at 1500bp and 3000bp. The 500bp and 1500bp fragment show stronger intensity to allow easier identification. All fragments are 'blunt-ended'. The GenLadder can be directly labeled at the 5'-end with radioisotopes using T4 polynucleotide Kinase for visualisation by autoradiography. Fragment sizes (in base pairs): 3000 bp (40ng/6µL), 2x 1500 bp (70ng/6µL), 1000 bp (50ng/6µL), 900 bp (40ng/6µL), 800 bp (40ng/6µL), 700 bp (30ng/6µL), 600 bp (30ng/6µL), 2x 500 bp (90ng/6µL), 400 bp (40ng/6µL), 300 bp (30ng/6µL), 200 bp (40ng/6µL), 100 bp (40ng/6µL). The DNA marker is already dissolved in buffer containing orange G and Xylene cyanol FF as tracking dyes. The total concentration of the DNA-Marker is 90 µg/mL. The recommended amount of DNA marker per lane is 0,5μg (6µL). GenLadder DNA ladders are available in a ready-to-use format (premixed with 6X DNA Loading Dye): M3084 (GenLadder 1kbp extended up to 25 kbp ready-to-use) > and M3328 (GenLadder 1kbp ready-to-use) > or our ready-to-use premix M3072 (GenLadder 50bp) > with 6X Orange DNA Loading Dye. The DNA Gel Loading Dyes can also be ordered separately: M3308 (DNA Gel Loading Dye with Bromophenol and Xylene Cyanol FF) >, M3321 (DNA Gel Loading Dye with Orange G) >.

ProbeMasterMix FAST without ROX is optimised for fast qPCR assays with probes in block systems. The master mix is optimized for fast PCR with short denaturation 2-step cycles. This 2X Mastermix is ready-to-use and contains all components for a successful and reliable qPCR with the exception of primer and template DNA. Advantages of the Hotstart Taq polymerase used in the Genaxxon ProbeMasterMix: Hotstart technology enables setup of PCR mixture at room temperature. short initial denaturation of not more than 2 minutes. optimized for 2-step PCR protocols. No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon Hotstart Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The hotstart formulation inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Probe qPCR master mix without ROX contains all the necessary components in an optimized composition to carry out quantitative PCR. hotstart Taq DNA Polymerase dATP, dCTP, dGTP, dTTP optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1mL simplifies handling and storage (less freeze-thaw cycles per aliquote) This Mastermix is specially suited for the following instruments: BioRad CFX96 Touch™, CFX384 Touch™, CFX Connect™, DNA Engine Opticon® 2, Chromo4™, iCycler iQ™ and My iQ™ , Roche LightCycler® 480, LightCycler® 1536, LightCycler® Nano, LightCycler® 96 and QuantStudio™ instruments, Thermo Scientific™ PikoReal™, Cepheid SmartCycler®, Bio Molecular Systems Mic qPCR cycler, Qiagen Rotor Gene Q, Rotor Gene 6000, MyGo Mini and MyGo Pro. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

GreenMasterMix FAST Blue with 500nM ROX is optimised for realtime PCR assays in block systems. This 2X Mastermix is ready-to-use and contains all components for a successful and reliable qPCR with the exception of primer and template DNA. Advantages of the HotStart Taq DNA polymerase used in the Genaxxon GreenMasterMix: Hotstart technology enables setup of PCR mixture at room temperature. short initial denaturing time of not more than 2 minutes No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The chemical modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Green qPCR master mix Blue with 500nM ROX contains all the necessary components in an optimized composition to carry out quantitative PCR: chemically modified Taq DNA Polymerase dATP, dCTP, dGTP, dTTP intercalating green fluorescent dye optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) This Mastermix is specially suited for the following instruments: Applied Biosystems® 5700, 7000, 7300, 7700, 7900, 7900 HT, Eppendorf Realplex4, StepOne™ and StepOnePlus™. Other realtime PCR master mixes from Genaxxon are: M3023 - GreenMastermix No ROX >, M3045 - ProbeMastermix No ROX >, M3011 - GreenMastermix Low ROX >, M3031 - ProbeMastermix Low ROX >, M3052 - GreenMastermix High ROX >, M3010 - ProbeMastermix High ROX >.

ProbeMasterMix FAST with 500nM  ROX optimised for fast realtime PCR assays in block systems. This master mix is ready-to-use and contains all components for a successful and reliable quantitative PCR with the exception of primer and template DNA. Advantages of the Hotstart Taq polymerase used in the Genaxxon ProbeMasterMix: Hotstart technology enables setup of PCR mixture at room temperature. short initial denaturation of not more than 2 minutes. optimized for 2-step PCR protocols. No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon Hotstart Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The hotstart formulation inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Probe qPCR master mix with 500nM ROX contains all the necessary components in an optimized composition to carry out quantitative PCR. hotstart Taq DNA Polymerase dATP, dCTP, dGTP, dTTP optimized reaction buffer 500nM ROX as internal reference stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) This Mastermix is specially suited for the following instruments: Applied Biosystems® 5700, 7000, 7300, 7700, 7900, 7900 HT, Eppendorf Realplex4, StepOne™ and StepOnePlus™. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

The SNP PolTaq DNA polymerase used for the SNP PolTaq 2X Master Mix has been specially designed for easy, reliable and rapid allele-specific discrimination, eg. CRISPR / Cas9 point mutations, for detecting incorrect CRISPR / Cas9 products, or validating sequencing results. The SNP PolTaq DNA polymerase distinguishes highly specific, whether a mismatch of the primer-template-complex is present or not. The mismatch (point mutation) must be at the 3 'end of the primer. Thus, mutant alleles can be distinguished exactly from wild-type alleles - without sequencing, since the polymerase simply does not amplify in the case of a mismatch. Just place your primer on the supposed point mutation (Important: The point mutation must be at the 3 'end) and the polymerase will detect a mismatch in this region with almost 100% accuracy: If the template base complementary to the 3' end of the primer shows the mutation and the primer does not, no amplification takes place - 100% certainty within a short time!The SNP PolTaq DNA polymerase can therefore be easily, time and cost-effectively used for the screening of point mutations. The SNP PolTaq DNA polymerase has 5'-3 'nuclease activity and can therefore be used for specific hydrolysi probes such as Taqman® probes or Molecular beacons. For more information on our SNP DNA polymerases and applications, read our blog now. DescriptionSNP PolTaq DNA polymerase is a highly selective DNA polymerase for the detection of Single Nucleotide Polymorphisms. It was developed specifically for allele-specific discrimination, where a very high discrimination rate is required e.g., in allele-specific PCR (ASA; AS-PCR), allele-specific primer extension (AS-PEX), SNP analysis, genotyping or in methylation-specific PCRs (MSP). Many other DNA polymerases tolerate mismatched primer-template complexes and are therefor not suitable. The SNP PolTaq DNA polymerase, on the other hand, distinguishes these specifically (high discrimination) and supplies only PCR products with perfectly matching primer pairs! The Genaxxon SNP Pol and SNP PolTaq DNA polymerases differ up to 100% by means of allele-specific PCR between the two alleles and, after a simple qPCR, give a clear result as to which allele is present. Thus, the principly great potential of the CRISPR/Cas9 technology can be used for human medicine and plant biotechnology especially together with the SNP PolTaq or SNP Pol DNA polymerase. Allele-specific PCR can be used to quantify the mutation rate in a pool or background of wild-type sequences. The verification of mutation frequencies determined by NGS can also be verified by means of allele-specific PCR and SNP Pol DNA polymerase. The SNP PolTaq DNA polymerase is very suitable for the analysis of liquid biopsy samples. With SNP PolTaq, the presence and frequency of cancer mutations can be analyzed and quantified very well. Picture below: Application note SNP Pol DNA Polymerase   We recommend short amplicon length (about 60-200 bp) for best results, but also longer amplicon lengths are possible. The addition of additional Magnesium (+0.5 - 1.5mM) might be needed in case of longer amplicons >500 bp.Trouble shooting: No bands after PCR of 30 cycles! Optimisation procedure for missing or weak bands.Annealing temperature is too low! Attention: The SNP PolTaq is an aptamer inhibited DNA polymerase. The aptamer oligo used reversibly inhibits the polymerase at temperatures <55°C! Therefore, the primers should ideally have an annealing temperature of >57°C. - realtime PCR approach - Check the dNTP concentration. This should be between 200 and 300µM (in the PCR). - Increase the number of cycles (at least 35, preferably equal to 40) Test optimisation - number of cyclesIn endpoint detection, a cycle count of 30 is not always sufficient to generate a clearly visible band. For example, with less than 200 DNA copies as a starting value. The test should therefore be run using real-time PCR, or five parallel PCRs should be used, one of which is taken from the PCR device after each of five different cycles (example below). Endpoint detection: Set up five identical PCR reactions in parallel using the SNP Pol DNA polymerase. Remove one of the PCR tubes from the cycler at each of 20, 25, 30, 35 and 40 cycles and apply all five reactions to an agarose gel at the end. This makes it easy to recognise which is the optimum number of cycles in the PCR for the given application (starting material, target, primer). SNP Pol PCR with cell lysates Animal cells and E.coli can be used directly for PCR with the SNP Pol DNA polymerase! No separate lysis or proteinase K digestion is necessary. PCR procedure:1. 50 - 500 cells are required per PCR batch! 2. prepare PCR mix with primers and buffer and place on ice! 3. add the picked colony directly to 10-20µL water (no separate lysis and no proteinase K digestion), vortex briefly (5 seconds), then add this cell suspension directly to the PCR reaction mixture, e.g. 10µL cell suspension for a PCR preparation with a total volume of 20µL. An initial denaturation time of 2-3 minutes is sufficient is sufficient, can be extended to 5 minutes if necessary. Genomic DNA per reaction max. 100 copies is relatively low, but should still work. The remainder of this cell suspension can also be frozen away in order to carry out further tests. Optional: 4. if possible: do real-time PCR!The SNP Pol DNA polymerase (M3009 > or M3061 >) can be used together with non-specific fluorescent dyes (eg Genaxxon's Green DNA Dye > or SybrGreen®) in real-time PCR. When working with specific PCR probes, only the SNP PolTaq DNA polymerase can be used, since only these have a 5'-3 'exonuclease activity. With our high quality dNTPs as Set (M3015.4100) > or Mix (M3016.1010) > or our DNALadders > and our favourable standard agarose (M3044) > we can offer additional products for your PCR. Application areas for SNP Pol DNA and SNP PolTaq DNA polymerase- Monitoring, verification and detection of point mutations- Identification of correct or wrong CRISPR/Cas9 products- Verification/validation of sequencing results- Quantification of mutations (e.g. NGS results)- SNP-detection by allele-specific amplification (ASA) / Allele-specific PCR- Methylation specific PCRs (MSP) after bisulfite treated DNA (CpG methylation sides)- HLA genotyping- micro sequencing- realtime PCR with hydrolysis probes- realtime multiplex PCRs - DamID-seq data in C. elegans. As an alternative to ChIP, DNA adenine methyltransferase identification by sequencing (DamID-seq) was recently shown to be able to characterize binding sites in single mammalian cells. Additionally, DamID can be achieved for cell-type specific analysis by expressing Dam fusion proteins under tissue specific promoters in a controlled manner. In this report, we present a user-friendly pipeline to analyse DamID-seq data in C. elegans. Sharma R, Ritler D, Meister P.Tools for DNA adenine methyltransferase identification analysis of nuclear organization during C. elegans development. Genesis. 2016 Feb 4. doi: 10.1002/dvg.22925. - Minisequencing SNP genotyping with SNPase DNA Polymerase can be carried out by the procedure described in: Lovmar L, Fredriksson M, Liljedahl U, Sigurdsson S, Syvänen AC. Quantitative evaluation by minisequencing and microarrays reveals accurate multiplexed SNP genotyping of whole genome amplified DNA. Nucleic Acids Res. 2003;31:e129. - Allel specific mismatch selectivity by the HiDi DNA polymerase Drum M, Kranaster R, Ewald C, Blasczyk R, Marx A (2014) Variants of a Thermus aquaticus DNA Polymerase with Increased Selectivity for Applications in Allele- and Methylation-Specific Amplification. PLoS ONE 9(5): e96640. doi:10.1371/journal.pone.0096640

GreenMastermix Low ROX optimised for realtime PCR assays in block systems that contains all components to perform quantitative PCR with the exception of primer and template DNA. This 2X Mastermix is ready-to-use and contains optimised amounts of all ingredients. Advantages of the chemically modified SuperHot Taq polymerase used in the Genaxxon GreenMasterMix: Hotstart technology enables setup of PCR mixture at room temperatur No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The chemical modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Green qPCR master mix high ROX contains all the necessary components in an optimized composition to carry out quantitative PCR: chemically modified Taq DNA Polymerase dATP, dCTP, dGTP, dTTP intercalating green fluorescent dye 50nM ROX optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) Stability at +2°C to +8°C (refrigerator): minimum of 8 months. This Mastermix is specially suited for the following instruments: Applied Biosystems® 7500, 7500 Fast and ViiA™ 7, QuantStudio™ instruments, Agilent Mx3000P™, Mx3005P™, Mx4000™ and AriaMx. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

SimplyEnlight PCR Starter-Kit – The All-in-One Solution for Efficient PCRFrom PCR to gel electrophoresis to visualization – all in just one preparation step!No additional pipetting of buffers or stains required. Save time and minimize contamination risks with the SimplyEnlight PCR Starter-Kit! Our innovative Red MasterMix Fluoro (2X) streamlines the PCR workflow by combining PCR amplification, gel loading dye, and nucleic acid staining in a single reaction. Additionally, the kit includes the pre-stained GenLadder 100 bp Plus, eliminating the need for extra staining.Your Key Benefits:Fast & efficient workflow – just one preparation step requiredNo additional gel staining – integrated fluorescent DNA stain for instant visualizationReduced contamination risk – fewer pipetting steps, improved reproducibilityNon-toxic fluorescent dye – environmentally friendly and safe disposalOptimized for screening & high-throughput applications – ideal for colony PCR and routine analysisContents of the SimplyEnlight PCR Starter-Kit: Red MasterMix Fluoro (2X) – the 3-in-1 solution: PCR MasterMix with DNA polymerase, buffer, dNTPs & MgCl₂ Integrated red loading dye for pipetting control Built-in fluorescent nucleic acid stain – no additional staining required GenLadder 100 bp Plus – pre-stained DNA marker:Instant DNA band visualization under UV or blue light No separate staining or pipetting required Loading Buffer I Fluoro (6X) – for additional DNA markers: Flexible use for staining extra DNA markers It doesn’t get any easier! With the SimplyEnlight PCR Starter-Kit, just mix your DNA and primers with the Red MasterMix Fluoro (2X) and start your PCR. After amplification, the PCR product can be analyzed and visualized via gel electrophoresis without any additional staining. Optimize your PCR workflow – with the SimplyEnlight PCR Starter-Kit from Genaxxon!

SNP Pol DNA polymerase for easy, reliable and rapid allele-specific discrimination, eg. CRISPR / Cas9 point mutations, for detecting incorrect CRISPR / Cas9 products, or validating sequencing results. The SNP Pol DNA polymerase distinguishes highly specific, whether a mismatch of the primer-template-complex is present or not. The mismatch (point mutation) must be at the 3 'end of the primer. Thus, mutant alleles can be distinguished exactly from wild-type alleles - without sequencing, since the polymerase simply does not amplify in the case of a mismatch. Just place your primer on the supposed point mutation (Important: The point mutation must be at the 3 'end) and the polymerase will detect a mismatch in this region with almost 100% accuracy: If the template base complementary to the 3' end of the primer shows the mutation and the primer does not, no amplification takes place - 100% certainty within a short time!The SNP Pol DNA polymerase can therefore be easily, time and cost-effectively used for the screening of point mutations. The variant SNP PolTaq DNA polymerase > has 5'-3 'nuclease activity and can therefore be used for specific hydrolysi probes such as Taqman® probes or Molecular beacons. For more information on our SNP DNA polymerases and applications, read our blog now. DescriptionSNP Pol DNA Polymerase is a highly selective DNA polymerase for the detection of Single Nucleotide Polymorphisms. It was developed specifically for allele-specific discrimination, where a very high discrimination rate is required e.g., in allele-specific PCR (ASA; AS-PCR), allele-specific primer extension (AS-PEX), SNP analysis, genotyping or in methylation-specific PCRs (MSP). Many other DNA polymerases tolerate mismatched primer-template complexes and are therefor not suitable. The SNP Pol DNA polymerase, on the other hand, distinguishes these specifically (high discrimination) and supplies only PCR products with perfectly matching primer pairs! The Genaxxon SNP Pol and SNP PolTaq DNA polymerases differ up to 100% by means of allele-specific PCR between the two alleles and, after a simple qPCR, give a clear result as to which allele is present. Thus, the principly great potential of the CRISPR/Cas9 technology can be used for human medicine and plant biotechnology especially together with the SNP PolTaq or SNP Pol DNA polymerase. Allele-specific PCR can be used to quantify the mutation rate in a pool or background of wild-type sequences. The verification of mutation frequencies determined by NGS can also be verified by means of allele-specific PCR and SNP Pol DNA polymerase. The SNP PolTaq DNA polymerase is very suitable for the analysis of liquid biopsy samples. With SNP PolTaq, the presence and frequency of cancer mutations can be analyzed and quantified very well. Picture below: Application note SNP Pol DNA Polymerase   We recommend short amplicon length (about 60-200 bp) for best results, but also longer amplicon lengths are possible. The addition of additional Magnesium (+0.5 - 1.5mM) might be needed in case of longer amplicons >500 bp.Trouble shooting: No bands after PCR of 30 cycles! Optimisation procedure for missing or weak bands.Annealing temperature is too low! Attention: The SNP Pol is an aptamer inhibited DNA polymerase. The aptamer oligo used reversibly inhibits the polymerase at temperatures <55°C! Therefore, the primers should ideally have an annealing temperature of >57°C. - realtime PCR approach - Check the dNTP concentration. This should be between 200 and 300µM (in the PCR). - Increase the number of cycles (at least 35, preferably equal to 40) Test optimisation - number of cyclesIn endpoint detection, a cycle count of 30 is not always sufficient to generate a clearly visible band. For example, with less than 200 DNA copies as a starting value. The test should therefore be run using real-time PCR, or five parallel PCRs should be used, one of which is taken from the PCR device after each of five different cycles (example below). Endpoint detection: Set up five identical PCR reactions in parallel using the SNP Pol DNA polymerase. Remove one of the PCR tubes from the cycler at each of 20, 25, 30, 35 and 40 cycles and apply all five reactions to an agarose gel at the end. This makes it easy to recognise which is the optimum number of cycles in the PCR for the given application (starting material, target, primer). SNP Pol PCR with cell lysates Animal cells and E.coli can be used directly for PCR with the SNP Pol DNA polymerase! No separate lysis or proteinase K digestion is necessary. PCR procedure:1. 50 - 500 cells are required per PCR batch! 2. prepare PCR mix with primers and buffer and place on ice! 3. add the picked colony directly to 10-20µL water (no separate lysis and no proteinase K digestion), vortex briefly (5 seconds), then add this cell suspension directly to the PCR reaction mixture, e.g. 10µL cell suspension for a PCR preparation with a total volume of 20µL. An initial denaturation time of 2-3 minutes is sufficient is sufficient, can be extended to 5 minutes if necessary. Genomic DNA per reaction max. 100 copies is relatively low, but should still work. The remainder of this cell suspension can also be frozen away in order to carry out further tests. Optional: 4. if possible: do real-time PCR!The SNP Pol DNA polymerase (M3009 > or M3061 >) can be used together with non-specific fluorescent dyes (eg Genaxxon's Green DNA Dye > or SybrGreen®) in real-time PCR. When working with specific PCR probes, only the SNP PolTaq DNA polymerase can be used, since only these have a 5'-3 'exonuclease activity. With our high quality dNTPs as Set (M3015.4100) > or Mix (M3016.1010) > or our DNALadders > and our favourable standard agarose (M3044) > we can offer additional products for your PCR. Application areas for SNP Pol DNA and SNP Pol DNA polymerase- Monitoring, verification and detection of point mutations- Identification of correct or wrong CRISPR/Cas9 products- Verification/validation of sequencing results- Quantification of mutations (e.g. NGS results)- SNP-detection by allele-specific amplification (ASA) / Allele-specific PCR- Methylation specific PCRs (MSP) after bisulfite treated DNA (CpG methylation sides)- HLA genotyping- micro sequencing- realtime PCR with hydrolysis probes- realtime multiplex PCRs - DamID-seq data in C. elegans. As an alternative to ChIP, DNA adenine methyltransferase identification by sequencing (DamID-seq) was recently shown to be able to characterize binding sites in single mammalian cells. Additionally, DamID can be achieved for cell-type specific analysis by expressing Dam fusion proteins under tissue specific promoters in a controlled manner. In this report, we present a user-friendly pipeline to analyse DamID-seq data in C. elegans. Sharma R, Ritler D, Meister P.Tools for DNA adenine methyltransferase identification analysis of nuclear organization during C. elegans development. Genesis. 2016 Feb 4. doi: 10.1002/dvg.22925. - Minisequencing SNP genotyping with SNPase DNA Polymerase can be carried out by the procedure described in: Lovmar L, Fredriksson M, Liljedahl U, Sigurdsson S, Syvänen AC. Quantitative evaluation by minisequencing and microarrays reveals accurate multiplexed SNP genotyping of whole genome amplified DNA. Nucleic Acids Res. 2003;31:e129. - Allel specific mismatch selectivity by the HiDi DNA polymerase Drum M, Kranaster R, Ewald C, Blasczyk R, Marx A (2014) Variants of a Thermus aquaticus DNA Polymerase with Increased Selectivity for Applications in Allele- and Methylation-Specific Amplification. PLoS ONE 9(5): e96640. doi:10.1371/journal.pone.0096640

GreenMasterMix without ROX optimised for realtime PCR assays in block systems that contains all components to perform quantitative PCR with the exception of primer and template DNA. This 2X Mastermix is ready-to-use and contains optimised amounts of all ingredients. Advantages of the chemically modified SuperHot Taq polymerase used in the Genaxxon GreenMasterMix: Hotstart technology enables setup of PCR mixture at room temperatur No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The chemical modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Green qPCR master mix without ROX contains all the necessary components in an optimized composition to carry out quantitative PCR: chemically modified Taq DNA Polymerase dATP, dCTP, dGTP, dTTP intercalating green fluorescent dye optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) Stability at +2°C to +8°C (refrigerator): minimum of 8 months. This Mastermix is specially suited for the following instruments: BioRad CFX96 Touch™, CFX384 Touch™, CFX Connect™, DNA Engine Opticon® 2, Chromo4™, iCycler iQ™ and My iQ™ , Roche LightCycler® 480, LightCycler® 1536, LightCycler® Nano, LightCycler® 96 and QuantStudio™ instruments, Thermo Scientific™ PikoReal™, Cepheid SmartCycler®, Bio Molecular Systems Mic qPCR cycler, Qiagen Rotor Gene Q, Rotor Gene 6000, MyGo Mini and MyGo Pro. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

GreenMastermix High ROX optimised for realtime PCR assays in block systems that contains all components to perform quantitative PCR with the exception of primer and template DNA. This 2X PCR master mix is ready-to-use and contains optimised amounts of all ingredients. Advantages of the chemically modified SuperHot Taq polymerase used in the Genaxxon GreenMasterMix: Hotstart technology enables setup of PCR mixture at room temperatur No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The chemical modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Green qPCR master mix high ROX contains all the necessary components in an optimized composition to carry out quantitative PCR: chemically modified Taq DNA Polymerase dATP, dCTP, dGTP, dTTP intercalating green fluorescent dye 500nM ROX optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) Stability at +2°C to +8°C (refrigerator): minimum of 8 months. This Mastermix is specially suited for the following instruments: Applied Biosystems® 5700, 7000, 7300, 7700, 7900, 7900 HT, Eppendorf Realplex4, StepOne™ and StepOnePlus™. Other realtime PCR master mixes from Genaxxon are: M3023 - GreenMastermix No ROX >, M3045 - ProbeMastermix No ROX >, M3011 - GreenMastermix Low ROX >, M3031 - ProbeMastermix Low ROX >, M3052 - GreenMastermix High ROX >, M3010 - ProbeMastermix High ROX >.

ProbeMasterMix without ROX optimised for realtime PCR assays in block systems that contains all components to perform quantitative PCR with the exception of primer and template DNA. This 2X Mastermix is ready-to-use and contains optimised amounts of all ingredients. Multiplex PCR: Applications at Genaxxon and at customers site have shown that the qPCR Probe Mastermix can be used for the simultaneous detection of up to four DNA targets in the same PCR reaction. For further details please refer to the product manual or contact us: info@genaxxon.com. Advantages of the chemically modified SuperHot Taq polymerase used in the Genaxxon ProbeMasterMix: Hotstart technology enables setup of PCR mixture at room temperatur No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The chemical modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Probe qPCR master mix without ROX contains all the necessary components in an optimized composition to carry out quantitative PCR. chemically modified Taq DNA Polymerase dATP, dCTP, dGTP, dTTP optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) Stability at +2°C to +8°C (refrigerator): minimum of 8 months. This Mastermix is specially suited for the following instruments: BioRad CFX96 Touch™, CFX384 Touch™, CFX Connect™, DNA Engine Opticon® 2, Chromo4™, iCycler iQ™ and My iQ™ , Roche LightCycler® 480, LightCycler® 1536, LightCycler® Nano, LightCycler® 96 and QuantStudio™ instruments, Thermo Scientific™ PikoReal™, Cepheid SmartCycler®, Bio Molecular Systems Mic qPCR cycler, Qiagen Rotor Gene Q, Rotor Gene 6000, MyGo Mini and MyGo Pro. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

ProbeMastermix High ROX optimised for realtime PCR assays in block systems that contains all components to perform quantitative PCR with the exception of primer and template DNA. This 2X Mastermix is ready-to-use and contains optimised amounts of all ingredients. Multiplex PCR: Applications at Genaxxon and at customers site have shown that the qPCR Probe Mastermix can be used for the simultaneous detection of up to four DNA targets in the same PCR reaction. For further details please refer to the product manual or contact us: info@genaxxon.com. Advantages of the Genaxxon ProbeMasterMix: Hotstart technology enables setup of PCR mixture at room temperatur No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The chemical modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Probe qPCR master mix high ROX contains all the necessary components in an optimized composition to carry out quantitative PCR: chemically modified Taq DNA Polymerase dATP, dCTP, dGTP, dTTP 500nM ROX optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) Stability at +2°C to +8°C (refrigerator): minimum of 8 months. This Mastermix is specially suited for the following instruments: Applied Biosystems® 5700, 7000, 7300, 7700, 7900, 7900 HT, Eppendorf Realplex4, StepOne™ and StepOnePlus™. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

ProbeMasterMix low ROX optimised for realtime PCR assays in block systems that contains all components to perform quantitative PCR with the exception of primer and template DNA. This 2X master mix is ready-to-use and contains optimised amounts of all ingredients. Multiplex PCR: Applications at Genaxxon and at customers site have shown that the qPCR Probe Mastermix can be used for the simultaneous detection of up to four DNA targets in the same PCR reaction. For further details please refer to the product manual or contact us: info@genaxxon.com. Advantages of the Genaxxon ProbeMasterMix: Hotstart technology enables setup of PCR mixture at room temperatur No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The chemical modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Probe qPCR master mix without ROX contains all the necessary components in an optimized composition to carry out quantitative PCR. chemically modified Taq DNA Polymerase dATP, dCTP, dGTP, dTTP 50nM ROX optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) Stability at +2°C to +8°C (refrigerator): minimum of 8 months. This Mastermix is specially suited for the following instruments: Applied Biosystems® 7500, 7500 Fast and ViiA™ 7, QuantStudio™ instruments, Agilent Mx3000P™, Mx3005P™, Mx4000™ and AriaMx. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

The SNP Pol DNA polymerase > used for the SNP Pol 2X Mastermix has been specially designed for easy, reliable and rapid allele-specific discrimination, eg. CRISPR / Cas9 point mutations, for detecting incorrect CRISPR / Cas9 products, or validating sequencing results. The SNP Pol DNA polymerase distinguishes highly specific, whether a mismatch of the primer-template-complex is present or not. The mismatch (point mutation) must be at the 3 'end of the primer. Thus, mutant alleles can be distinguished exactly from wild-type alleles - without sequencing, since the polymerase simply does not amplify in the case of a mismatch. Just place your primer on the supposed point mutation (Important: The point mutation must be at the 3 'end) and the polymerase will detect a mismatch in this region with almost 100% accuracy: If the template base complementary to the 3' end of the primer shows the mutation and the primer does not, no amplification takes place - 100% certainty within a short time!The SNP Pol DNA polymerase can therefore be easily, time and cost-effectively used for the screening of point mutations. The variant SNP PolTaq DNA polymerase has 5'-3 'nuclease activity and can therefore be used for specific hydrolysi probes such as Taqman® probes or Molecular beacons. For more information on our SNP DNA polymerases and applications, read our blog now. DescriptionSNP Pol DNA Polymerase and SNP PolTaq Polymerase are  highly selective DNA polymerase for the detection of Single Nucleotide Polymorphisms. It was developed specifically for allele-specific discrimination, where a very high discrimination rate is required e.g., in allele-specific PCR (ASA; AS-PCR), allele-specific primer extension (AS-PEX), SNP analysis, genotyping or in methylation-specific PCRs (MSP). Many other DNA polymerases tolerate mismatched primer-template complexes and are therefor not suitable. The SNP Pol DNA polymerase, on the other hand, distinguishes these specifically (high discrimination) and supplies only PCR products with perfectly matching primer pairs! The Genaxxon SNP Pol and SNP PolTaq DNA polymerases differ up to 100% by means of allele-specific PCR between the two alleles and, after a simple qPCR, give a clear result as to which allele is present. Thus, the principly great potential of the CRISPR/Cas9 technology can be used for human medicine and plant biotechnology especially together with the SNP PolTaq or SNP Pol DNA polymerase. Allele-specific PCR can be used to quantify the mutation rate in a pool or background of wild-type sequences. The verification of mutation frequencies determined by NGS can also be verified by means of allele-specific PCR and SNP Pol DNA polymerase. The SNP PolTaq DNA polymerase is very suitable for the analysis of liquid biopsy samples. With SNP PolTaq, the presence and frequency of cancer mutations can be analyzed and quantified very well. Picture below: Application note SNP Pol DNA Polymerase   We recommend short amplicon length (about 60-200 bp) for best results, but also longer amplicon lengths are possible. The addition of additional Magnesium (+0.5 - 1.5mM) might be needed in case of longer amplicons >500 bp.Trouble shooting: No bands after PCR of 30 cycles! Optimisation procedure for missing or weak bands.Annealing temperature is too low! Attention: The SNP Pol is an aptamer inhibited DNA polymerase. The aptamer oligo used reversibly inhibits the polymerase at temperatures <55°C! Therefore, the primers should ideally have an annealing temperature of >57°C. - realtime PCR approach - Check the dNTP concentration. This should be between 200 and 300µM (in the PCR). - Increase the number of cycles (at least 35, preferably equal to 40) Test optimisation - number of cyclesIn endpoint detection, a cycle count of 30 is not always sufficient to generate a clearly visible band. For example, with less than 200 DNA copies as a starting value. The test should therefore be run using real-time PCR, or five parallel PCRs should be used, one of which is taken from the PCR device after each of five different cycles (example below). Endpoint detection: Set up five identical PCR reactions in parallel using the SNP Pol DNA polymerase. Remove one of the PCR tubes from the cycler at each of 20, 25, 30, 35 and 40 cycles and apply all five reactions to an agarose gel at the end. This makes it easy to recognise which is the optimum number of cycles in the PCR for the given application (starting material, target, primer). SNP Pol PCR with cell lysates Animal cells and E.coli can be used directly for PCR with the SNP Pol DNA polymerase! No separate lysis or proteinase K digestion is necessary. PCR procedure:1. 50 - 500 cells are required per PCR batch! 2. prepare PCR mix with primers and buffer and place on ice! 3. add the picked colony directly to 10-20µL water (no separate lysis and no proteinase K digestion), vortex briefly (5 seconds), then add this cell suspension directly to the PCR reaction mixture, e.g. 10µL cell suspension for a PCR preparation with a total volume of 20µL. An initial denaturation time of 2-3 minutes is sufficient is sufficient, can be extended to 5 minutes if necessary. Genomic DNA per reaction max. 100 copies is relatively low, but should still work. The remainder of this cell suspension can also be frozen away in order to carry out further tests. Optional: 4. if possible: do real-time PCR!The SNP Pol DNA polymerase (M3009 > or M3061 >) can be used together with non-specific fluorescent dyes (eg Genaxxon's Green DNA Dye > or SybrGreen®) in real-time PCR. When working with specific PCR probes, only the SNP PolTaq DNA polymerase can be used, since only these have a 5'-3 'exonuclease activity. With our high quality dNTPs as Set (M3015.4100) > or Mix (M3016.1010) > or our DNALadders > and our favourable standard agarose (M3044) > we can offer additional products for your PCR. Application areas for SNP Pol DNA and SNP Pol DNA polymerase- Monitoring, verification and detection of point mutations- Identification of correct or wrong CRISPR/Cas9 products- Verification/validation of sequencing results- Quantification of mutations (e.g. NGS results)- SNP-detection by allele-specific amplification (ASA) / Allele-specific PCR- Methylation specific PCRs (MSP) after bisulfite treated DNA (CpG methylation sides)- HLA genotyping- micro sequencing- realtime PCR with hydrolysis probes- realtime multiplex PCRs - DamID-seq data in C. elegans. As an alternative to ChIP, DNA adenine methyltransferase identification by sequencing (DamID-seq) was recently shown to be able to characterize binding sites in single mammalian cells. Additionally, DamID can be achieved for cell-type specific analysis by expressing Dam fusion proteins under tissue specific promoters in a controlled manner. In this report, we present a user-friendly pipeline to analyse DamID-seq data in C. elegans. Sharma R, Ritler D, Meister P.Tools for DNA adenine methyltransferase identification analysis of nuclear organization during C. elegans development. Genesis. 2016 Feb 4. doi: 10.1002/dvg.22925. - Minisequencing SNP genotyping with SNPase DNA Polymerase can be carried out by the procedure described in: Lovmar L, Fredriksson M, Liljedahl U, Sigurdsson S, Syvänen AC. Quantitative evaluation by minisequencing and microarrays reveals accurate multiplexed SNP genotyping of whole genome amplified DNA. Nucleic Acids Res. 2003;31:e129. - Allel specific mismatch selectivity by the HiDi DNA polymerase Drum M, Kranaster R, Ewald C, Blasczyk R, Marx A (2014) Variants of a Thermus aquaticus DNA Polymerase with Increased Selectivity for Applications in Allele- and Methylation-Specific Amplification. PLoS ONE 9(5): e96640. doi:10.1371/journal.pone.0096640

SNP Pol DNA polymerase for easy, reliable and rapid allele-specific discrimination, eg. CRISPR / Cas9 point mutations, for detecting incorrect CRISPR / Cas9 products, or validating sequencing results. The SNP Pol DNA polymerase distinguishes highly specific, whether a mismatch of the primer template complex is present or not. The mismatch (point mutation) must be at the 3 'end of the primer. Thus, mutant alleles can be distinguished exactly from wild-type alleles - without sequencing since the polymerase simply does not amplify in the case of a mismatch. Just place your primer on the supposed point mutation (Important: The point mutation must be at the 3 'end) and the polymerase will detect a mismatch in this region with almost 100% accuracy: If the template base complementary to the 3' end of the primer shows the mutation and the primer does not, no amplification takes place - 100% certainty within a short time!The SNP Pol DNA polymerase can therefore be easily, time and cost-effectively used for the screening of point mutations. SNP PolTaq DNA polymerase shows also 5'-3'-nuclease activity and is therefore suitable for hydrolysis probe-based assays (Taqman®, molecular beacons, etc.). For more information on our SNP DNA polymerases and applications, read our blog now. DescriptionSNP PolTaq DNA Polymerase is a highly selective DNA polymerase for the detection of Single Nucleotide Polymorphisms. It was developed specifically for allele-specific discrimination, where a very high discrimination rate is required e.g., in allele-specific PCR (ASA; AS-PCR), allele-specific primer extension (AS-PEX), SNP analysis, genotyping or in methylation-specific PCRs (MSP). Many other DNA polymerases tolerate mismatched primer-template complexes and are therefor not suitable. The SNP Pol DNA polymerase, on the other hand, distinguishes these specifically (high discrimination) and supplies only PCR products with perfectly matching primer pairs! The Genaxxon SNP Pol and SNP PolTaq DNA polymerases differ up to 100% by means of allele-specific PCR between the two alleles and, after a simple qPCR, give a clear result as to which allele is present. Thus, the principle great potential of the CRISPR/Cas9 technology can be used for human medicine and plant biotechnology especially together with the SNP PolTaq or SNP Pol DNA polymerase. Allele-specific PCR can be used to quantify the mutation rate in a pool or background of wild-type sequences. The verification of mutation frequencies determined by NGS can also be verified by means of allele-specific PCR and SNP Pol DNA polymerase. The SNP PolTaq DNA polymerase is very suitable for the analysis of liquid biopsy samples. With SNP PolTaq , the presence and frequency of cancer mutations can be analyzed and quantified very well. Picture below: Application note SNP PolTaq DNA Polymerase   We recommend short amplicon length (about 60-200 bp) for best results, but also longer amplicon lengths are possible. The addition of additional Magnesium (+0.5 - 1.5mM) might be needed in case of longer amplicons >500 bp.Trouble shooting: No bands after PCR of 30 cycles! Optimisation procedure for missing or weak bands.Annealing temperature is too low! Attention: The SNP PolTaq is an aptamer inhibited DNA polymerase. The aptamer oligo used reversibly inhibits the polymerase at temperatures <55°C! Therefore, the primers should ideally have an annealing temperature of >57°C. - realtime PCR approach - Check the dNTP concentration. This should be between 200 and 300µM (in the PCR). - Increase the number of cycles (at least 35, preferably equal to 40) Test optimisation - number of cyclesIn endpoint detection, a cycle count of 30 is not always sufficient to generate a clearly visible band. For example, with less than 200 DNA copies as a starting value. The test should therefore be run using real-time PCR, or five parallel PCRs should be used, one of which is taken from the PCR device after each of five different cycles (example below). Endpoint detection: Set up five identical PCR reactions in parallel using the SNP Pol DNA polymerase. Remove one of the PCR tubes from the cycler at each of 20, 25, 30, 35 and 40 cycles and apply all five reactions to an agarose gel at the end. This makes it easy to recognise which is the optimum number of cycles in the PCR for the given application (starting material, target, primer). SNP Pol PCR with cell lysates Animal cells and E.coli can be used directly for PCR with the SNP Pol DNA polymerase! No separate lysis or proteinase K digestion is necessary. PCR procedure:1. 50 - 500 cells are required per PCR batch! 2. prepare PCR mix with primers and buffer and place on ice! 3. add the picked colony directly to 10-20µL water (no separate lysis and no proteinase K digestion), vortex briefly (5 seconds), then add this cell suspension directly to the PCR reaction mixture, e.g. 10µL cell suspension for a PCR preparation with a total volume of 20µL. An initial denaturation time of 2-3 minutes is sufficient is sufficient, can be extended to 5 minutes if necessary. Genomic DNA per reaction max. 100 copies is relatively low, but should still work. The remainder of this cell suspension can also be frozen away in order to carry out further tests. Optional: 4. if possible: do real-time PCR!The SNP Pol DNA polymerase (M3009 > or M3061 >) can be used together with non-specific fluorescent dyes (eg Genaxxon's Green DNA Dye > or SybrGreen®) in real-time PCR. When working with specific PCR probes, only the SNP PolTaq DNA polymerase can be used, since only these have a 5'-3 'exonuclease activity. With our high quality dNTPs as Set (M3015.4100) > or Mix (M3016.1010) > or our DNALadders > and our favourable standard agarose (M3044) > we can offer additional products for your PCR. Application areas for SNP Pol DNA and SNP PolTaq DNA polymerase- Monitoring, verification and detection of point mutations- Identification of correct or wrong CRISPR/Cas9 products- Verification/validation of sequencing results- Quantification of mutations (e.g. NGS results)- SNP-detection by allele-specific amplification (ASA) / Allele-specific PCR- Methylation specific PCRs (MSP) after bisulfite treated DNA (CpG methylation sides)- HLA genotyping- micro sequencing- realtime PCR with hydrolysis probes- realtime multiplex PCRs - DamID-seq data in C. elegans. As an alternative to ChIP, DNA adenine methyltransferase identification by sequencing (DamID-seq) was recently shown to be able to characterize binding sites in single mammalian cells. Additionally, DamID can be achieved for cell-type specific analysis by expressing Dam fusion proteins under tissue specific promoters in a controlled manner. In this report, we present a user-friendly pipeline to analyse DamID-seq data in C. elegans. Sharma R, Ritler D, Meister P.Tools for DNA adenine methyltransferase identification analysis of nuclear organization during C. elegans development. Genesis. 2016 Feb 4. doi: 10.1002/dvg.22925. - Minisequencing SNP genotyping with SNPase DNA Polymerase can be carried out by the procedure described in: Lovmar L, Fredriksson M, Liljedahl U, Sigurdsson S, Syvänen AC.bQuantitative evaluation by minisequencing and microarrays reveals accurate multiplexed SNP genotyping of whole genome amplified DNA. Nucleic Acids Res. 2003;31:e129. - Allel specific mismatch selectivity by the HiDi DNA polymerase Drum M, Kranaster R, Ewald C, Blasczyk R, Marx A (2014) Variants of a Thermus aquaticus DNA Polymerase with Increased Selectivity for Applications in Allele- and Methylation-Specific Amplification. PLoS ONE 9(5): e96640. doi:10.1371/journal.pone.0096640

Deoxynucleotide (dNTP) Solution Mix as an equimolar solution of ultrapure, HPLC purified (>99%) dATP, dCTP, dGTP and dTTP for qPCR, RT-PCR, standard PCR, and Klenow reactions. The Genaxxon dNTP solutions are optimized for use in DNA amplification and other related methods. The Genaxxon dNTPs and dNTP-mixes contain no measurable bacterial or human DNA. For long term storage and/or for repeated use we do recommend to aliquot the stock solutions. Mixture of dNTP sodium salts (dATP, dCTP, dGTP und dTTP) Concentration: 10 mM each nucleotide Please have also a look on our broad range of nucleotides especially the dNTP mix withv2 mM dNTP mix , our dNTP set, or modified nucleotides, e.g. Biotin-11-dUTP. You can get additional products for your successful PCR as our Taq DNA Polymerse (M3001), or our proof-reading polymerases Pfu (M3004), Pwo (M3002) and ReproFast (M3003), as well as the ready-to-use RedMastermix (M3029), already including dNTPs.

Highly pure, HPLC purified dNTPs (>99%) delivered as a 2 mM solution of dATP, dCTP, dGTP and dTTP for use in qPCR, standard PCR, RT-PCR and Klenow reactions. Use 5 µL of Mix for PCR in 50µL reaction volume.The Genaxxon dNTP mix is optimized for its use in DNA polymerisation and related methods. Our dNTPs contain no measurable bacterial or human DNA. For storage for a prolonged periode of time we recommend to prepare small aliquots, especially in case of rare use. Mixture of dNTP sodium salt solutions (dATP, dCTP, dGTP und dTTP) Concentration: 2 mM of ach nucleotide Please have also a look on our broad range of nucleotides especially the dNTP mix with 10 mM dNTP mix, our dNTP set , or modified nucleotides, e.g. Biotin-11-dUTP. You can get additional products for your successful PCR as our Taq DNA Polymerse (M3001), or our proof-reading polymerases Pfu (M3004), Pwo (M3002) and ReproFast (M3003), as well as the ready-to-use RedMastermix (M3029), already including dNTPs.

High-quality Taq DNA Polymerase from Genaxxon is a highly processive 5' - 3' DNA Polymerase, lacking 3' - 5' exonuclease activity. The high processivity and fidelity of Genaxxon bioscience Taq Polymerase allows amplification of DNA fragment of up to >7 kb. Genaxxon bioscience Taq Polymerase is delivered with 10X reaction buffer and separate MgCL2.The enzyme is delivered with our buffer component 'Buffer-S'. The buffer is optimised for high specificity amplification of DNA-templates. Our complete buffer contains 15mM MgCl2. Free Taq DNA Polymerase test sample available!No shipping costs within Germany. With our high quality dNTPs as Set (M3015.4100 and M3015.0250) or Mix (M3016.1010) or our DNA Ladders and our favourable standard agarose (M3044) we can offer additional high quality products for your PCR.

High-quality Taq DNA Polymerase from Genaxxon is a highly processive 5' - 3' DNA Polymerase, lacking 3' - 5' exonuclease activity. The high processivity and fidelity of Genaxxon bioscience Taq Polymerase allows amplification of DNA fragment of >7 kb. Genaxxon bioscience Taq Polymerase is delivered with 10X reaction buffer and separate MgCL2.The enzyme is delivered with our buffer component 'Buffer-E'. The buffer is optimised for high yield amplification of DNA-templates. Our complete buffer contains 25mM MgCl2. Taq DNA Polymerase test sample available! No shipping costs within Germany. With our high quality dNTPs as Set (M3015.4100 and M3015.0250) or Mix (M3016.1010) or our DNA Ladders and our favourable standard agarose (M3044) we can offer additional high quality products for your PCR.

GreenMasterMix FAST without ROX is optimised for fast qPCR assays without probes in block systems. The master mix is optimized for fast PCR with short denaturation 2-step cycles. This 2X Mastermix is ready-to-use and contains all components for a successful and reliable qPCR with the exception of primer and template DNA. Advantages of the HotStart Taq DNA polymerase used in the Genaxxon GreenMasterMix: Hotstart technology enables setup of PCR mixture at room temperature. short initial denaturing time of not more than 2 minutes No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Green qPCR master mix without ROX contains all the necessary components in an optimized composition to carry out quantitative PCR: Hotstart Taq DNA Polymerase dATP, dCTP, dGTP, dTTP intercalating green fluorescent dye optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) Stability at +2°C to +8°C (refrigerator): minimum of 8 months. This Mastermix is specially suited for the following instruments: BioRad CFX96 Touch™, CFX384 Touch™, CFX Connect™, DNA Engine Opticon® 2, Chromo4™, iCycler iQ™ and My iQ™ , Roche LightCycler® 480, LightCycler® 1536, LightCycler® Nano, LightCycler® 96 and QuantStudio™ instruments, Thermo Scientific™ PikoReal™, Cepheid SmartCycler®, Bio Molecular Systems Mic qPCR cycler, Qiagen Rotor Gene Q, Rotor Gene 6000, MyGo Mini and MyGo Pro. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

GreenMasterMix FAST with 500nM ROX is optimised for realtime PCR assays in block systems. This 2X Mastermix is ready-to-use and contains all components for a successful and reliable qPCR with the exception of primer and template DNA. Advantages of the HotStart Taq DNA polymerase used in the Genaxxon GreenMasterMix: Hotstart technology enables setup of PCR mixture at room temperature. short initial denaturing time of not more than 2 minutes No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Green qPCR master mix with 500nM ROX contains all the necessary components in an optimized composition to carry out quantitative PCR: Hotstart Taq DNA Polymerase dATP, dCTP, dGTP, dTTP intercalating green fluorescent dye optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) This Mastermix is specially suited for the following instruments: Applied Biosystems® 5700, 7000, 7300, 7700, 7900, 7900 HT, Eppendorf Realplex4, StepOne™ and StepOnePlus™. Further realtime PCR Mastermixes and realtime FAST PCR Mastermixes can be found here: qPCR (Classic qPCR > or FAST and Multiplex qPCR >).

GreenMasterMix FAST with 50nM ROX is optimised for realtime PCR assays in block systems. This 2X Mastermix is ready-to-use and contains all components for a successful and reliable qPCR with the exception of primer and template DNA. Advantages of the HotStart Taq DNA polymerase used in the Genaxxon GreenMasterMix: Hotstart technology enables setup of PCR mixture at room temperature. short initial denaturing time of not more than 2 minutes No pipetting on ice necessary anymore No immediate further processing (PCR) necessary. The pipetted pre-PCR mixtures can be left at RT for up to 3 days. Amplification of GC-rich templates High yields No Primer dimers The Genaxxon SuperHot Taq DNA polymerase offers convenience and practicality, without compromising efficiency or specificity: 1. The modification inhibits the polymerase, which prevents false priming at all temperatures tested, allowing for PCR reactions to be set up at RT (20°C to 25°C), and 2. "High mix stability allows pre-assemby of the plate in advance", which means PCR reactions can be prepared and stored at RT for up to three days before they are run, without affecting the results. The Green qPCR master mix with 50nM ROX contains all the necessary components in an optimized composition to carry out quantitative PCR: Hotstart Taq DNA Polymerase dATP, dCTP, dGTP, dTTP intercalating green fluorescent dye optimized reaction buffer stabilizers and enhancers to enable even amplification of low copy number targets 50nM internal passive reference fluorescence dye the small aliquote size of 1.25mL simplifies handling and storage (less freeze-thaw cycles per aliquote) This Mastermix is specially suited for the following instruments: Applied Biosystems® 7500, 7500 Fast and ViiA™ 7, QuantStudio™ instruments, Agilent Mx3000P™, Mx3005P™, Mx4000™ and AriaMx. Other realtime PCR master mixes from Genaxxon are: M3023 - GreenMastermix No ROX >, M3045 - ProbeMastermix No ROX >, M3011 - GreenMastermix Low ROX >, M3031 - ProbeMastermix Low ROX >, M3052 - GreenMastermix High ROX >, M3010 - ProbeMastermix High ROX >.